PV Pulley (J Section), 12 Groove, 180 OD, Style P2
PV Pulley – Section J
• All Challenge pulleys are produced from cast iron or steel and have a phosphated finish for protection
• V, Multiple Groove and PV pulleys are balanced to Q6.3 or better allowing them to run at peripheral (rim) speeds up to 40 m/s
• Available in sections J, K and L sections
• Manufactured from GG25 high grade cast iron
Challenge PV pulleys are manufactured according to ISO 9982 specification (Pulleys and V-ribbed belts for industrial applications). This encompasses product designation, geometry, roughness and pulley run out.
PV Pulley – Section J
PV pulleys offer high-power transmission (up to 600kW) and efficiency (up to 98%) with a low belt system profile when compared to V-Belts or flat belts. The smaller flat belt profile allows smaller pulleys to be used, higher peripheral speeds (up to 60m/s) along with providing enough power transmission to run multiple output shafts from one drive.
The increase in peripheral speed and power transmission is achieved by combining the low profile of flat belts with the increased contact area of v-belts. Up to several v-belts can be replaced by a single PV belt and pulley which eliminates the need for belt matching and extensive belt inventories.
The standard Challenge range of PV pulleys covers the J, K and L sections, with special pulleys for the H and M section belts available upon request. Standard pulleys are supplied with either a taper bore to suit our range of taper bushes, or pilot bores.
Groove dimensions of PV pulleys conform to ISO 9982
Standard and custom - V and Timing Belt Pulleys
To complement our wide range of belts, we also manufacture and supply a range of standard and bespoke pulleys for our V belts and Timing belts. Manufactured from cast iron or steel, our pulley grooves are machine cut for accuracy and also statically or dynamically balanced (depending upon their size) to grade Q6.3 or better giving peripheral (rim) speeds of up to 40m/s.
The complete range of pulleys available from Challenge are manufactured from high grade close grain GG25 grey cast iron or steel before being phosphated for protection. Metric timing pulleys are also available from lightweight aluminium with a natural finish.
Shaft fixing option vary due to the large range of sizes and materials available, but as standard the range of pulleys come with either a taper bore, pilot bore or both types of bores.
V Belt Pulleys
With high quality machined groves and availability from nearly 20 official locations around world, these cost effective and readily available range of pulleys have proven themselves countless times over the last 40 years. Coupled with our wide range of Shaft Mounted Speed Reducers, they offer a reliable method of reducing motor speeds, which has become an industry standard.
Available to suit both wedge and classical belts to ISO 4184. Groove dimensions conform to ISO 4183 for both eccentricity of outside diameter to bore and groove side wobble tolerance.
All pulleys are available with a taper bore to suit the Challenge range of stock taper bushes although pilot and QD bush bore pulleys can also be manufactured.
A wide range of non-standard styles and sizes up to a diameter of 2400mm can be produced.
PV pulleys are also available for sections J, K and L
Timing Belt Pulleys
Working in precision applications globally, our range of timing belts and corresponding pulleys have been developed around the industries that we supply daily. With our ability to manufacture special pulleys or offer light weight solutions from aluminium we can offer a solution for a vast array of precision drive systems.
Timing belt pulleys are available for the standard Classical, HTD Profile and Metric belts. Classical L and H pulleys are available with a taper bore as are 5M, 8M and 14M HTD Profile pulleys. All other sizes are available in pilot bore including the complete range of Metric timing pulleys. If you require a taper bore for a Metric or large Classical pulley, then these can often be manufactured to order.
Unit of Sale; Per Item
|Pulley - Belt Range||J|
|Pulley - No. Of Grooves or Teeth||12|
|Pulley - Outside Diameter||180|
|Pulley - Hub Diameter||120|
|Pulley - Recess Diameter||160|
|Pulley - Rim Width||32.5|
|Pulley - Distance Thro.||45|
|Pulley - Pilot Bore Diameter||-|
|Pulley - Bush Size||2517|
|Pulley Config And Style||P2|
|Pulley - Hub Length||6.25|